• Camera included

    $89.99Price

    Snap kit designed for the Five33 Switchback frame in a hybrid setup (six inch rear arms, five inch front), fitting all Switchback variants with at least five inch prop clearance.  Sports a massive sixty-five degree fixed camera angle.  There are a lot of Switchback builds out there nowadays, but simply nothing compares to one running this extreme Snap kit.  The lowest drag, lowest profile, lowest lap time modification on the market for the Switchback masses, by Snap Aerial Silhouettes.

     


     

                                                Features

    Super-resolution, semi-flex TPU canopy construction, advanced material boasts a 580% elongation coefficient, 95A shore hardness rating, and peerless, opaquely reflective finish; less jello than nylon, and no cracking in cold weather.

     

    Proven Bleeding Shell passively retractable camera mount, which lets the camera slide back into the protected area of the canopy during direct hits and hard crashes, tested for absolutely no unintended camera slippage.

     

    Stainless steel internal threads for far greater aerodynamic efficacy than traditional exposed-hardware designs, while still mounting using the frame's stock hardware.

     

    Onboard, internally wired LED array made up of one Tiny's Pico Rainbow RGB LEDs, and one Tiny's Tiny Rainbow v2 LEDs (digitally addressable as a seven node string).


     

     

                                                 Notice

    THIS KIT ASSUMES THE USE OF ZIPTIE/ARM MOUNTED RADIO SIGNAL RECEIVER ANTENNAE, AND LIGHTWEIGHTCIRCULAR POLARIZED OR LINEAR VIDEO TRANSMISSION ANTENNAE.

     

    THIS KIT ASSUMES MAXIMUM RACING QUADCOPTER BUILD PROWESS DUE TO EXTREMELY LOW FLIGHT STACK HEIGHT ACCOMODATIONS (YOU WILL HAVE THE ABSOLUTE LOWEST PROFILE BUILD WITH THIS KIT, BUT YOU NEED THE SKILL TO BUILD IT), SEE AN EXAMPLE ON OUR COMPANY PAGE AT ROTORBUILDS.COM

     

    THIS CANOPY DOES NOT ENSURE TURTLE MODE FUNCTIONALITY DUE TO DESIGN FOR EXTREMELY LOW AERODYNAMIC PROFILE, THE KIT IS RECOMMENDED ONLY FOR PROFESSIONAL PILOTS OPERATING OUTSIDE HINDRANCES OF FREQUENT CRASHING.

     


     

                                              Interfacing

    The red wire from the canopy goes to 5V on the flight controller, the black wire from the canopy goes to ground on the flight controller, and the yellow wire from the canopy goes to the LED signal output on the flight controller; the included RunCam Racer Nano should be wired according to its digital manual, using the provided JST pigtail.

     

    Canopy mounts using the frame's stock hardware.  Apply medium strength threadlocker to camera screws, but DO NOT apply any threadlocker to canopy mounting screws.

     


     

                                                Fitment

    Only guaranteed to fit the included RunCam Racer Nano camera, which features an extremely low profile and mass, state of the art gesture control, and optical performance equal to that of the RunCam Racer 2.

     

    Camera saving feature setup video: https://www.instagram.com/tv/CAeRJ9_gtAe/?igshid=13aaiv2k98i2y


     

     

                                              Contents

    One Snap canopy, one RunCam Racer Nano camera in its original packaging, four black contractor quality Cambridge zipties for radio signal receiver/video transmission antennae mounting, five stainless steel BelMetric nyloc aero-propnuts, five black Pyro Drone Hyperlite machined aluminum propeller shaft spacers, one JST pigtail for the canopy, and one JST pigtail for the camera.

     

     

     

                                                Weight

    Canopy-with internal components, adhesives, and inserts-weighs approximately 18.6 grams, and the RunCam Racer Nano weighs 3.5 grams.

    For best viewing adjust zoom on your browser and refresh until this message is aligned with the "select" button

    SNAP.

    T M

    S N A P   A E R I A L   S I L H O U E T T E S .   ™